Precast Slabs for Crossings Prove Safer and Quieter
Precast slabs across highway railroad crossings reduce tire wear and vehicle damage, improving safety and comfort for motorists. They span tracks, lowering maintenance costs by avoiding plank replacements, and can be cast in winter, with lifting sockets allowing easy removal. Slabs resist wear and provide durable, low‑maintenance crossings in busy roads and industrial driveways.
Focus of Headlights Adjustment Guide
A dated advisory explains checking headlight focus by adjusting then testing against garage rear walls with bright lights. It suggests noting the parking spot, reassessing after each garage entry, and correcting any misalignment promptly to save time and worry.
Safety Driving Rules From a Historic Notice
Instructions emphasize steady control and caution while driving. Key points include avoid speeding, dim headlights, slow at intersections, keep eyes forward, hug curb when slow, avoid passing on the right, keep both hands on the wheel, ensure brakes, signal turns or slowdowns, and caution when transporting children. Guidance also advises proper left turns and staying in the correct lane.
Old Automobiles as Junk Worth More Than Trade Value
Old cars three years old and older are heavy with metal and now worth mainly junk value. Dealers hold heirlooms in corners, hoping for a high trade allowance that never comes. With rising junk metal prices, the practical choice is to sell to an iron buyer and reclaim space.
Internal Friction Heats Tires in Road Contact
The heating of automobile tires after long fast runs mainly arises from internal friction within the tire rather than road friction. As the tire deflects against the road, the tire’s plies move against each other, generating heat. greater shape changes increase friction, while higher air pressure reduces deflection but cannot eliminate heat.
Kerosene dangers noted beyond common uses
Kerosene, though versatile, can damage metal and equipment. It can eat through rust in rusty oil cans, leaving a compromised container. Washing a roll bearing with kerosene can trap residue and dilute grease, causing improper drying. Using kerosene to flush engines risks remaining solvent diluting fresh oil.
Tightening Prevents Rattles In Mechanical Components
Rattles come from loose or worn parts. Loose parts stem from loose nuts and should be tightened regularly. Worn components mainly result from lack of lubrication, so proper lubrication reduces wear and rattles over time.
Meat Is Chief Use for Pure Breds
United States Department of Agriculture reports that about 62 percent of pure bred livestock are marketed for meat. Purebred animals cost slightly more or less to raise than scrubs or grades, with dairy cattle costing a bit more. About 96 percent of those using purebred sires trial them for all stock classes, and nearly all progressive farmers advocate rigid culling and selling only worthy stock for breeding.
MENTIONED IN THIS ARTICLE
United States Department of Agriculture
Bureau of Animal Industry
Grass Seed Comes From Many Different States
Grass seed sources span the United States with red-top seed predominating from the southern end of the state and Missouri and Tawa contributing small amounts. Northern Kentucky and northwestern Missouri supply most northern high-grass mixtures, while meadow fescue seeds come from eastern Kansas and less so from Missouri Kentucky and southern Indiana. Arizona and California mainly furnish Bermuda grass seed for southern use.
MENTIONED IN THIS ARTICLE
Wincle
Tawa
Missouri
Kentucky
Towa
Kansas
Indiana
Arizona
California
Spraying Potato Vines to Fight Beetles in Gardens
The article advises spraying potato vines to control striped Colorado potato beetle and gray blister beetle. It recommends 50 gallons of water mixed with 1.4 pounds paris green or 4 pounds lead arsenate, with equal quantity of lime to prevent burning, and notes dusting mixes such as 1 part poison to 20 parts hydrated lime and mentions home garden use of paris green.
Setting Out Raspberry Plants for Fall or Spring
Raspberry plants may be set out in either fall or spring with a preference for spring. Keep beds weed free by cultivation until late June, then ease cultivation and let late weeds grow until the next spring, and cultivate again. Tops should be cut back in early spring before growth starts to hip or waist height.
Also Mentioned on This Page
Lincoln Highway
OUR Comic
Little
Tom and
Mickie
GeOrGe WashinGton
Uesse
Western Newspaper Union
Fanny
Vai
Caim